18T pinion, 76T spur
A 18T pinion on a 76T spur is a 4.222:1 spur ratio. With an assumed 2.72:1 internal ratio that is a 11.48:1 final drive, which on a 3300KV motor at 2S with 4.3 in tires works out to about 27.2 mph theoretical and 23.1 mph realistic.
48P 3.175mm Pinion Gear Sets 5Pack 13T 14T 15T 16T 17T Hardened
- 1/8
Pinion sets in 48P, the pitch this 76T spur uses. Buying a set lets you step one tooth at a time instead of guessing.
$9.99 listed price, changes often
Check price on AmazonWhat final drive does 18/76 give?
The spur ratio is 76 / 18 = 4.222. Your car's transmission or differentials multiply it. The internal ratio varies by model, so here is the final drive across the common range; find yours in the manual next to the gearing chart.
| Internal ratio | Final drive (FDR) | Character |
|---|---|---|
| 2:1 | 8.44:1 | typical 1/10 basher range |
| 2.5:1 | 10.56:1 | typical 1/10 basher range |
| 2.72:1 | 11.48:1 | typical 1/10 basher range |
| 3:1 | 12.67:1 | typical 1/10 basher range |
| 3.5:1 | 14.78:1 | short: torque, cooler |
How fast is 18/76?
Example: a 1/10 2WD truck geared for speed on 2S, 3300KV motor, 4.3 in tires and an assumed 2.72:1 internal ratio (FDR 11.48:1). Theoretical speed is a no-load ceiling; the realistic figure assumes about 85 percent of it, which is typical on stock tires. For your own motor and tires, use the gear ratio and top speed calculator.
| Battery | Motor RPM | Theoretical | Realistic |
|---|---|---|---|
| 2S LiPo (7.4 V) | 24,420 | 27.2 mph | 23.1 mph |
What does one tooth up or down do?
Speed scales with the pinion on a fixed spur. The heat rating compares each option with 18T, assuming 18T runs at a sensible temperature today.
| Swap | Speed change | Motor heat |
|---|---|---|
| 18T to 16T | -11.1% | cooler |
| 18T to 20T | +11.1% | moderate |
Which cars use a 76T 48P spur?
The 76T spur on this page is sold in 76T, 83T, 86T and 90T sets for Traxxas Slash and Rustler 2WD. Pitch matters more than tooth count: 48P gears only mesh with 48P gears. Set the mesh with a strip of paper between the gears as you tighten the motor, then remove it; there should be a tiny amount of play. See how to change a pinion gear.
18T on other spurs
- 18/86 (48P): 4.78:1
- 18/90 (48P): 5.00:1
- 18/83 (48P): 4.61:1
- 18/57 (0.8 mod): 3.17:1
- 18/46 (Mod 1): 2.56:1
- 18/50 (Mod 1): 2.78:1
Every pinion on the 76T spur
- 16T / 76T: 4.75:1
- 20T / 76T: 3.80:1
- 22T / 76T: 3.46:1
- 24T / 76T: 3.17:1
- 26T / 76T: 2.92:1
- 28T / 76T: 2.71:1
Gears and a thermometer for this swap
Get this list emailed to you
Every pick on this page with its current price in one email, so you can decide later. One email, no sequence.
Frequently asked questions
What is the gear ratio of 18/76?
76 divided by 18 is 4.222, so the spur ratio is 4.22:1. The final drive ratio multiplies that by your car's internal transmission or differential ratio, which is printed in the manual. At a 2.72:1 internal ratio it is 11.48:1; at 3:1 it is 12.67:1. Use the calculator with your own internal ratio for an exact figure.
Is 18T faster than 17T on a 76T spur?
Yes. On the same spur, speed scales with pinion teeth, so 18T is about 5.9 percent faster than 17T at the same motor RPM. The motor also works harder at every speed, so it runs warmer. Check the temperature after two or three minutes of running before going up another tooth.
Will a 18T 48P pinion fit my car?
Only if the spur is also 48P and the motor mount has enough adjustment for the pinion size. Pitch must match exactly; 48P gears will not mesh correctly with other pitches. Bore size must match the motor shaft, commonly 3.175 mm (1/8 in) on 1/10 motors and 5 mm on larger motors. The spur here is sold in 76T, 83T, 86T and 90T sets for Traxxas Slash and Rustler 2WD.
RCCarCalc is researched guidance, not professional advice. Figures come from published manufacturer specifications, listings and verified owner reports, not hands-on testing. Speeds are theoretical or as listed; real results depend on gearing, battery, tires and terrain. See how we research.