16T pinion, 83T spur
A 16T pinion on a 83T spur is a 5.188:1 spur ratio. With an assumed 2.72:1 internal ratio that is a 14.11:1 final drive, which on a 3300KV motor at 2S with 4.3 in tires works out to about 22.1 mph theoretical and 18.8 mph realistic.
48P 3.175mm Pinion Gear Sets 5Pack 13T 14T 15T 16T 17T Hardened
- 1/8
Pinion sets in 48P, the pitch this 83T spur uses. Buying a set lets you step one tooth at a time instead of guessing.
$9.99 listed price, changes often
Check price on AmazonWhat final drive does 16/83 give?
The spur ratio is 83 / 16 = 5.188. Your car's transmission or differentials multiply it. The internal ratio varies by model, so here is the final drive across the common range; find yours in the manual next to the gearing chart.
| Internal ratio | Final drive (FDR) | Character |
|---|---|---|
| 2:1 | 10.38:1 | typical 1/10 basher range |
| 2.5:1 | 12.97:1 | typical 1/10 basher range |
| 2.72:1 | 14.11:1 | short: torque, cooler |
| 3:1 | 15.56:1 | short: torque, cooler |
| 3.5:1 | 18.16:1 | short: torque, cooler |
How fast is 16/83?
Example: a 1/10 2WD stadium or short course truck, 3300KV motor, 4.3 in tires and an assumed 2.72:1 internal ratio (FDR 14.11:1). Theoretical speed is a no-load ceiling; the realistic figure assumes about 85 percent of it, which is typical on stock tires. For your own motor and tires, use the gear ratio and top speed calculator.
| Battery | Motor RPM | Theoretical | Realistic |
|---|---|---|---|
| 2S LiPo (7.4 V) | 24,420 | 22.1 mph | 18.8 mph |
| 3S LiPo (11.1 V) | 36,630 | 33.2 mph | 28.2 mph |
What does one tooth up or down do?
Speed scales with the pinion on a fixed spur. The heat rating compares each option with 16T, assuming 16T runs at a sensible temperature today.
| Swap | Speed change | Motor heat |
|---|---|---|
| 16T to 14T | -12.5% | cooler |
| 16T to 18T | +12.5% | high |
Which cars use a 83T 48P spur?
The 83T spur on this page is listed as fitting Traxxas 1/10 Slash, Stampede, Rustler and Bandit 2WD models. Pitch matters more than tooth count: 48P gears only mesh with 48P gears. Set the mesh with a strip of paper between the gears as you tighten the motor, then remove it; there should be a tiny amount of play. See how to change a pinion gear.
16T on other spurs
- 16/86 (48P): 5.38:1
- 16/90 (48P): 5.63:1
- 16/76 (48P): 4.75:1
- 16/87 (48P): 5.44:1
- 16/57 (0.8 mod): 3.56:1
- 16/46 (Mod 1): 2.88:1
- 16/50 (Mod 1): 3.13:1
Every pinion on the 83T spur
Gears and a thermometer for this swap
Get this list emailed to you
Every pick on this page with its current price in one email, so you can decide later. One email, no sequence.
Frequently asked questions
What is the gear ratio of 16/83?
83 divided by 16 is 5.188, so the spur ratio is 5.19:1. The final drive ratio multiplies that by your car's internal transmission or differential ratio, which is printed in the manual. At a 2.72:1 internal ratio it is 14.11:1; at 3:1 it is 15.56:1. Use the calculator with your own internal ratio for an exact figure.
Is 16T faster than 15T on a 83T spur?
Yes. On the same spur, speed scales with pinion teeth, so 16T is about 6.7 percent faster than 15T at the same motor RPM. The motor also works harder at every speed, so it runs warmer. Check the temperature after two or three minutes of running before going up another tooth.
Will a 16T 48P pinion fit my car?
Only if the spur is also 48P and the motor mount has enough adjustment for the pinion size. Pitch must match exactly; 48P gears will not mesh correctly with other pitches. Bore size must match the motor shaft, commonly 3.175 mm (1/8 in) on 1/10 motors and 5 mm on larger motors. The spur here is listed as fitting Traxxas 1/10 Slash, Stampede, Rustler and Bandit 2WD models.
RCCarCalc is researched guidance, not professional advice. Figures come from published manufacturer specifications, listings and verified owner reports, not hands-on testing. Speeds are theoretical or as listed; real results depend on gearing, battery, tires and terrain. See how we research.